Jump to content

2003 Chevy Evap Vent Solenoid

1997xltlimited

Recommended Posts

1997xltlimited Enthusiast

1997xltlimited

Posted
Posted

I am having troubles with my new truck, new to me anyways. 2003 Chevy 1500 4.8L 4x4. The check enginge light came on so I aksed a friend to hook it up to his computer and it was diagnosed as the evap vent solenoid. He said it wasnt to big of a deal and reset the code. It stayed off for about two weeks and now it is back on. The question I have is I looked for the part online and it seems rather expensive, well over 100 dollars. Is there any other aftermarket parts that would fit this truck. I cannot afford to spend that kind of money on it right now. Also how do you get the clips the hose off that piece. It has some type of clip on it. Newbie asking for a little help.. Thanks in advance!

1997xltlimited Enthusiast

1997xltlimited

Posted
  • Author
Posted

I found the solenoid, two question how do you get the hoses off without wrecking the clips that hold the hose. Second is there an easy way to access this piece, its seems to be a really tight squeeze in there.

 

thanks

  • 1 month later...
1997xltlimited Enthusiast

1997xltlimited

Posted
  • Author
Posted

I took the part off and cleaned it out about a month ago or so. Had the code reset and it came back on today. Can somebody tell me the cheapest replacement part I can get and the part number. Mine was a little thin rectangle box. Thanks!!!!

1997xltlimited Enthusiast

1997xltlimited

Posted
  • Author
Posted

has anybody tried the following parts on a 2003, It says 2004 and newer

 

 

 

***IMPORTANT INFORMATION YOU MUST READ*****

 

Ok everyone, listen up....If you have a 04 and newer silverado, with a failed evap vent solenoid, you have to read this info. Do not pay $100+ for this part(actually $150.00 at the dealer). The following part numbers associated with this part have been gm#19207763,19152349, and AC DELCO #'s 214-2082 costing over $100.00 for the modified part. This is for the modified part, with the relocation of the filterbox, and the added hose that seperates the two. No one at Gm will tell you this, but this same part, that was origionally on your silverado, is also used in the 2006 Suburban. It will be an identical replacement for what is ON YOUR TRUCK, and the cost is $24.04 AT THE DEALER. I know this because I own a 2006 silverado, and a 2006 suburban. Looked at the suburban when the part went bad on the silverado(from overfilling the tank)and bingo, same part. Ask a parts person at GM, and they will tell you otherwise, but they are lying to you. Bought the suburban part today part # 25932571 (GM #) and everything is identical, right down to the numbers stamped on the part itself. Took the part off my silverado, put the replacement on (which gm told me is not the right part), cleared the codes, and bingo no more light after 3 consecutive starts...... Why, is it that GM feels we need to pay the price for something they did wrong???? And moreso, lie to us, telling us the $150.00 part is our only choice to fix the problem. My truck went 40K miles with the origional part, and probably only went bad because of my own stupidity in overfilling the tank, whay would I not just want to spend $24.00 to put on the same part, that will probably go the rest of the life of the truck with no tank overfills???? I say CLASS ACTION LAWSUIT FOR EVERYONE THAT HAS BEEN SCAMMED INTO PAYING THE RIDICULOUS PRICE that GM is trying to suck out of us.....Please pass this on to the world, and every forum you can...Get the word out....Let the parts people at GM know we are on to their BS, and they can't take advantage of us like they have.....

jro909 Senior Enthusiast

jro909

Posted
Posted

evap canisters take shits because of the crap design and people topping off the tank

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,860
    Total Members
    8,960
    Most Online
    HWN808
    Newest Member
    HWN808
    Joined

  • Who's Online   6 Members, 0 Anonymous, 1,092 Guests (See full list)

  • Latest Articles

  • Posts

    • OnTheReel
      Some Assembly is Required

      By OnTheReel · Posted

      https://www.gm-trucks.com/why-gm-chose-0w-30-gen-6-v8-oil/   The swing back to reality continues…
    • richard wysong
      Gas Prices

      By richard wysong · Posted

      Diesel $5.42 at the truck stop on the hi-way
    • Chuck FB
      Joke Thread

      By Chuck FB · Posted

    • txab
      Gas Prices

      By txab · Posted

      $3.59  
    • needafix
      2019+ Brake failure, it's complicated

      By needafix · Posted

      I'm not sure if this should be a new topic, let me know if it's out of place. This my first post. Thanks 85077522 - AC Delco GM Genuine Parts Brake Master Cylinders. Anyone else had to replace this brake master cylinder yet. I didn't do any brake work, it looks like new parts and I've had the truck for about 4k miles, 119k total miles.  When it started to throw codes I did the calibrations with a bidirectional scanner and got the codes to clear but they came back so I did the routine; base bleed, automated bleed and final base bleed. All that with Bosch ES16-32N fluid (please look it up). That seemed to fix it but 100ish miles later it failed again so I ran the same process but with a pressure bleeder this time and got the same results, fixed for 100ish miles. The original fluid looked bad and I thought I got most of it out, it could've been the wrong fluid. The codes; P25A2, C05B0-00, C2A1B. I can get them to clear but not for long. The C05B0 indicates a leak in the front circuit (which is bone dry) so I'm thinking of doing the bleed process on that front again today and I don't know if that's taboo to just do the front but at this point it seems like it's worth the try anyway. The new master cylinder/module unit is supposed to get here today. But now I'm pretty much convinced this install is over my head. I've called several shops and some mobile guys that I know but this thing is like radio active material, scary wise. I did get 2 local shops say they should be able to do it, one says he has the SPS2 programing capability. And with the battery disconnected is there supposed to be pedal resistance, mine is to the floor, then if I pump it I can get some resistance. I had a panic stop prior to this issue which may have contributed from what I read. And on the first attempt to bleed and hydraulic test the scanner listed things to look for and one was any gaps between the pad and rotors which I did notice on the RF corner and I removed the outer pad (where the gap was) cleaned it and the hardware and didn't see a gap after that but will re-check it. I read that if pushing the caliper pistons back then you're supposed to open the bleeder so as to not push fluid backwards into the abs module or it will damage it. If that's true then that's also a possibility from the previous owner having the brakes changed before I got it. I'm using an XTool ip500 scanner. Any suggestions, questions and comments welcome. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...